blog banner


A-1 Form A,C-1 Form C. Ag Alloy. 1AAVAC/24VDC 10A VAC. 1CA VC/24VDC,10A/ 6A VAC. TV VAC/24VDC. 15A. 1,VA,W. S. Coil Voltage. DC5V. -. -. Coil Sensitivity: Blank – Standard (mW) Important Notice: This data sheet and its contents (the “Information”) belong to the. HKE HRS4H-S-DC5V datasheet, Relay (1-page), HRS4H-S-DC5V datasheet, HRS4H-S-DC5V pdf, HRS4H-S-DC5V datasheet pdf, HRS4H-S-DC5V pinouts.

Author: Tygolkree Majind
Country: Serbia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 24 September 2006
Pages: 293
PDF File Size: 10.68 Mb
ePub File Size: 19.44 Mb
ISBN: 922-7-18177-298-7
Downloads: 6296
Price: Free* [*Free Regsitration Required]
Uploader: Arajas

Home Questions Tags Users Unanswered.

This high-density System-in-Package SiP integrates controller, power switches, and support components. That module you saw probably has at the very least a transistor included to actually drive the relay. A simple low side NPN switch is usually the easiest way to control a relay from a digital output.

These ICs are driver chips, and they are what actually drive the relays.

WhatRoughBeast 49k 2 28 Dtasheet is Web Browser. Your Arduino most likely can’t drive that relay directly. Virgin Galactic — Commercial Space Flight.

What’s missing? Tell us about it.

In a basic relay there are three contactors: Sign up using Email and Password. You aren’t going to be able to drive this relay directly from the digital output of a microcontroller. This voltage is called the operating voltage. Jun 1 ’15 at Olin Lathrop k 30 And I have no idea why your module can run without connecting d5v.

If you don’t have an Arduino, you obviously don’t have an Arduino pin 7 to drive the relay. SPI Module of Arduino.

find VCC, GND and IN in relay – Electrical Engineering Stack Exchange

Get inner details about structure of a relay switch. Choosing Motor For Robots. Relay is an electromagnetic device which is used to isolate two circuits electrically and connect them magnetically. When the operating voltage is applied the relay coil gets energized and the COM changes contact to NO.


Interface GPS with Arduino.

Email Required, but never shown. Commonly used relays are available in different configuration of operating voltages like 6V, 9V, 12V, 24V etc.

Post as a guest Name. Relays are sometimes used for their electrical isolation between their input the coil and their output the switch contacts. Here’s your relay’s datasheet: Interface SD Card with Arduino. What you have in your picture is a plain old relay. I have googled with first result as a part’s datasheet with exact pinout. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Thus a small sensor circuit can drive, say, a fan or an electric bulb. It may be that you are connecting it to the power supply ground that also connects to the Arduino, but in that case you datashset, in fact, electrically connecting it to the Arduino. The resistance between each of these datawheet and any of the other three will be infinite.

HRS4H-(S)-DC5V Datasheet PDF –

The input section has a coil which generates magnetic field when a small voltage from an electronic circuit is applied to it. Choosing Battery for Robots. The relays in the link you provided do not have a Vcc connection, and they have only 5 pins. To find out which is which, use a ohmmeter. There are many questions here already on that topic, so no need to dc5g the details in this answer.


The NO pin will have infinite reistance to all other pins. This will often tell you the voltage or current the coil requires to activate the switch, and what the switch is rated for. You are probably better off purchasing a ready-made module that has the appropriate driver transistor and back-EMF diode already installed. Skip to main content. Do you hrsh4 a part number? They are often used to interface brs4h electronic circuit working at a low voltage to an electrical circuit which works at very high voltage.

HRS4H-S-DC5V Datasheet PDF

Sign up or log in Sign up using Google. By using proper combination of contactors, the electrical circuit can be switched on and off. There will be some finite resistance between the two coil leads, probably a few 10s of Ohms, maybe up to or two Ohms. They are very hhrs4h devices and allow one circuit to switch another one while they are completely separate.

So the module as a whole has 10 pins. As such, there is often a larger physical distance between these two sets of pins. What is the problem? Flip the relay over and look at what x printed on the top.

This guess is based on the fact that there are two of them grouped separately from the others.