Throughout this manual, the following conventions are used for SCPI command syntax. • Square brackets .. HEWLETT-PACKARD,EA,0,X.X-X.X-X.X. Read about ‘EA Triple Output DC Power Supply User’s Guide’ on element14 .com. EA Triple Output DC Power Supply User’s Guide. Items are supplied with manuals, accessories and typically a full no-quibble 2 . HP EA/32A/33A/34A Programmable DC Power Supply Specifications.
|Published (Last):||5 October 2008|
|PDF File Size:||14.34 Mb|
|ePub File Size:||3.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
Chapter 5 Error Messages Execution Errors Program mnemonic too long A command header was received which contained more than the maximum 12 characters allowed.
An item that has been used previously. Add to watch list Remove from watch list. Speed of Response -Programming Down Figure shows that when the power supply is programmed down, the regulator senses that the output voltage is higher than desired and turns off the series transistors entirely.
Chapter 3 Front-Panel Operation Disabling the Outputs Disabling the Outputs The outputs of the power supply can be disabled or enabled from the front panel using key. Report item – opens in a new window or tab. General Information This chapter provides a general description of your power supply. Input Power Requirements The power supply is shipped from the factory with a power-line cord that has a plug appropriate for your location. See other items More Minimum monthly payments are required.
When ordering from the US, parcels may be subject to import tax and duty charges, which the buyer is responsible to pay. Sell now – Have one to sell? Message 10 of I am able to control almost every settings of the power supply voltage at each channel, limit current at each channeletc. Delivery times may vary, especially during peak periods. That terminal must be connected to earth ground through a power source with a 3-wire ground receptacle. Chapter 7 Tutorial Remote Programming Remote Programming During remote programming a constant-voltage regulated power supply is called upon to change its output voltage rapidly.
Programming Ranges And Output Identifiers The following table lists the programming ranges, output names, and output numbers for each output. Numeric Parameters Commands that require numeric parameters will accept all commonly used decimal representations of numbers including optional signs, decimal points, and scientific notation.
Select a valid country. Check the list of parameters to verify that you have used a valid parameter type. The cable and adapter pin diagram are shown below. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used.
AGILENT TECHNOLOGIES EA USER MANUAL Pdf Download.
Store The operating state yp now stored. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. Each is controlled by a control circuit that provides voltages to program the outputs. Chapter 7 Tutorial Connecting the Load Load Consideration Capacitive Loading In most cases, the power supply will be stable for almost any size load capacitance.
When the front-panel ERROR annunciator turns on, one or more command syntax or hardware errors have been detected. Thanks in advance, Diogo Ribeiro Diogo Ribeiro.
This program sets the output voltages and currents for 30! Mouse over to E3631w – Click to enlarge. Page 6 Display Annunciators Adrs Power supply is addressed to listen or talk over a remote interface. Message 9 of HP A Function Generator.
Hewlett Packard E3631A Triple Output DC Power Supply HP 6v 5a
Skip to main content. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab. You must return items in their original packaging and in the same condition as when you received them. Hewlett-Packard B Pulse Generator. Queries return either output values or internal instrument settings.
DB Serial Connection If your computer or terminal has a hhp serial port with a male connector, use the null-modem cable and pin adapter included with the Agilent A Cable Kit. Back to home page. Page Chapter 7 Tutorial Connecting the Load Reverse Current Msnual An active load connected to the supply may actually deliver a reverse current to the supply during a maual of its operating cycle.
Delivery time is estimated using our proprietary method which is based on the buyer’s proximity to the item location, the shipping service selected, the seller’s shipping history, and other factors.
Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to watch list.
OpenDocument In the last step you have to replace the original dll file in the directory Your power supply was calibrated before it left the factory. Will usually post within 1 business day of receiving cleared payment – opens in a new window or tab.
This item will be shipped through the Global Shipping Program and includes international tracking. Estimated on or before Tue.
This amount is subject to change until you make payment. Get the item you ordered or get your money back. Learn More – opens in a new window or tab Any international shipping and import charges are paid in part to Pitney Bowes Inc. Triggering Commands Chapter 4 Remote Interface Reference Triggering Commands Triggering Commands The power supply’s triggering system allows a change in voltage and current when receiving a trigger, to select a trigger source, and to insert a trigger.
Chapter 7 Tutorial Remote Programming If no load resistor is attached to the power supply output terminal, then the output voltage will rise linearly at a rate of C when programmed upward, andthe shortest possible up-programming time.