L O A D I N G
blog banner

HITACHI 42HDS69 MANUAL PDF

This stand for use only with Hitachi 42HDS .. owner’s manual of each component for the location of video and audio inputs and outputs. instructions. Find the user manual you need for your TV and more at ManualsOnline. Hitachi 42HDS69 Flat Panel Television User Manual. Page 1. Page 2. Download Manual for Model 42HDS69 HITACHI PLASMA PartsDirect has parts, manuals & part diagrams for all types of repair projects.

Author: Kagataxe Muramar
Country: Haiti
Language: English (Spanish)
Genre: Travel
Published (Last): 1 March 2009
Pages: 486
PDF File Size: 4.91 Mb
ePub File Size: 9.80 Mb
ISBN: 417-5-43801-852-6
Downloads: 30572
Price: Free* [*Free Regsitration Required]
Uploader: Kelkis

BTW, I did call Hitachi customer support.

Hitachi Flat Panel Television 42HDS69 User Guide |

Page of 88 Go. Page 44 Locks Locks This function will block out the picture and sound of the selected channel or video input. See important marking located on bottom of stand. Voltage IT11 1 4 2 mwnual 3 1. VESA is a trademark of a nonprofit organization. Connect the other end Arrow mark facing front to the swivel slot of the Table Top Stand. If it is damaged, the module will not function unless the glass-panel is hitavhi with a new glass-panel.

Using wood screws two fasten the set to the clamping screw holes on the rear of the Plasma Display stand as shown below.

This remote is designed to operate different types of cable boxes. Voltage IW03 1 1. Checking Procedure 1 Check the brightness as below. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into hotachi the device will be installed.

  BANDAGEM FUNCIONAL OMBRO PDF

Hitachi 42HDS69 Operating Manual

It may take a few seconds for the sequence. The following guidelines and procedures should be followed whenever this condition is hhitachi. When carrying PDP module, watch surrounding objects, such as tables, and also do not carry it alone since it may be dangerous and it will be damaged due to excessive stress to the module glass-panel.

These can generate electrical charges sufficient to damage ES devices. This remote is designed to operate different types of cable boxes. How To Set Up Your New Hitachi Plasma Television To take measures to prevent the Plasma Television from tipping over and prevent possible injury it is important to mount the unit in a stable and flat surface. Connect insulated gauge jumper wire from the nearest component on one side of the pattern break to the lead of the nearest component on the other side.

This slot is for the CableCARD that will be hitaci by your local cable operator to gain access chosen cable channels.

Below are illustrations and names of common connectors. Power Swivel Move Select 1. In some cases, this may cause the temperature of the panel surface to increase.

To remove a solder bridge, use hifachi de-solder braid as shown in the figure below. For best performance, video and audio cables should be made from coaxial shielded wire. Comments to this Manuals Your Name.

In case the flexible printed circuits are damaged, the corresponding addressed portions of the screen will not be lit and exchange of a glass panel will be required.

  FOUNDATIONS OF BILINGUAL EDUCATION AND BILINGUALISM COLIN BAKER PDF

HITACHI 42HDS69 OPERATING MANUAL Pdf Download.

Voltage CN63 1 5. Carefully bend each IC lead against the circuit foil pad and solder it. Any current measured must not exceed 0. Troubleshooting Troubleshooting Items Notes A buzzing sound may be heard when the plasma television is turned on in a very quiet Buzzing sound from Plasma room.

Do not connect the test fixture ground strap to any heatsink in this instrument. Plug the adapter into the antenna terminal on the TV. Device Settings response of the device to this command. Troubleshooting Items Notes A buzzing sound may be heard when the plasma television is turned on in a very quiet Buzzing sound from Plasma room. Voltage CN64 1 Use these connections in place of the standard video connection if your device has this feature.

Answered on Jun 01, You must first program the remote to match the remote system of your DVD player refer to pages for pre-codes.

Using an insulation tester DCVconnect one htiachi its leads to the AC plug jumper and touch with the other lead each exposed metal part antennas, screwheads, metal overlays, control shafts, etc. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. I tried exactly that but it did not work.