L O A D I N G
blog banner

DMO565R DATASHEET PDF

DMOR Datasheet PDF, DMOR datasheet, DMOR pdf, DMOR pinout, DMOR data, circuit, ic, manual, substitute, parts. Description. The FSDMRE, FSDMRE and FSDMRE are an integrated Pulse Width Modulator (PWM) and. SenseFET specifically designed for. Features. • Optimized for Quasi-Resonant Converter (QRC). • Advanced Burst- Mode Operation for under 1W Standby. Power Consumption. • Pulse-by-Pulse.

Author: Goltishicage Gardalmaran
Country: Papua New Guinea
Language: English (Spanish)
Genre: Life
Published (Last): 21 September 2004
Pages: 110
PDF File Size: 17.6 Mb
ePub File Size: 10.29 Mb
ISBN: 127-3-53641-632-1
Downloads: 76774
Price: Free* [*Free Regsitration Required]
Uploader: Fenrigrel

At the instant datasheef internal Sense FET is turned on, there usually exists a high current spike through the Sense FET, caused by primary-side capacitance and secondary-side rectifier reverse recovery. Compared with discrete MOSFET and PWM controller solution, it can reduce total cost, component count, size and weight simultaneously increasing efficiency, productivity, and system reliability. At startup, the internal high datashedt current source supplies internal bias and charges the external capacitor that is connected to the Vcc pin.

This pin is connected directly to the high voltage DC link. Since D1 is blocked when the feedback voltage Vfb exceeds 2. This pin is the positive supply voltage input. Then, Vfb climbs up in a similar manner to the over load situation, forcing the preset maximum current to be supplied to the SMPS until fatasheet over load protection is activated.

DMR Datasheet, PDF – Alldatasheet

Comparing the feedback voltage with the voltage across the Rsense resistor plus an offset voltage makes it possible to control the switching duty cycle. These parameters indicate the inductor current. In this condition, Vfb continues increasing until it reaches 6V, when the switching operation is terminated as shown in Figure 7. These parameters, although guaranteed at the design, are not tested in mass production.

The delay time for shutdown is the time required to charge CB from 2. Texas Instruments – Subject: Therefore, the peak value of the current through the Sense FET is limited.

This event typically happens when the input voltage is increased or the output load is decreased. In this generation the startup resistor is replaced by an internal high voltage current source.

  LUST FU2000 PDF

dwtasheet The PWM controller includes integrated fixed frequency oscillator, under voltage lockout, leading edge blanking Datasheeetoptimized gate driver, internal soft start, temperature compensated precise current sources for a loop compensation and self protection circuitry. The typical soft start time is 10msec, The pulse width to the power switching device is progressively increased to establish the correct working conditions for transformers, inductors, and capacitors.

Excessive voltage across the Rsense resistor would lead to incorrect feedback operation in the current mode PWM control.

SN datasheet – doctor- SN datasheet Author: Because more energy than required is provided to the output, the output voltage may exceed the rated voltage before the over load protection is activated, resulting vatasheet the breakdown of the devices in the secondary side.

Because these protection circuits are fully integrated into the IC without external components, the reliability can be improved without increasing cost.

DMO565R даташиты PDF

In order to avoid undesired activation of OVP during normal operation, Vcc should be designed to be below 19V. Ql5 datasheet pdf -? Free standing with no heat-sink under natural convection. Dmo565g this situation, the protection circuit should be activated in order to protect the SMPS. Rockchip RK datasheet V0. Overload is defined as the load current exceeding a pre-set level due to an unexpected event.

However, even when the SMPS is in the normal operation, the over load protection circuit can be activated during the load transition.

DMOR Datasheet –

SN datasheet datashedt Texas Instruments Documents. When Vcc reaches the UVLO stop voltage, 8V, the protection is reset and the internal high voltage current source charges the Vcc capacitor via the Vstr pin.

TempShutDown Delay Current vs. Then, the FSDMRB dmo565f its normal switching operation and the power is supplied from the auxiliary transformer winding unless Vcc goes below the dmoo565r voltage of 8V.

When the reference pin voltage of the KA exceeds the internal reference voltage of 2. Once Vcc reaches 12V, the internal current source is disabled. During start up, the power is supplied by an internal high voltage current source that is connected to the Vstr pin.

It also helps to prevent transformer saturation and reduce the stress on the secondary diode during startup. Ql5 datasheet pdf QL5 datasheet, Maximum practical continuous power in an open frame design at 50C ambient.

  MAGIC QUADRANT FOR CRM MULTICHANNEL CAMPAIGN MANAGEMENT 2011 PDF

This device is an integrated high voltage power switching regulator which combine an avalanche rugged Sense FET with a current mode PWM control block. The voltage on the output capacitors is progressively increased with the intention of smoothly establishing the required output voltage.

The collector of an opto-coupler is typically tied to this pin.

As the load decreases, the feedback voltage decreases. In this manner, the auto-restart can alternately enable and disable the switching of the power Sense FET until the fault condition is eliminated see Figure 6. Pulse width limited by maximum junction temperature 2.

Pulse width modulation PWM circuit2. This causes the feedback voltage to rise. At this point switching stops and the output voltages start to drop at a rate dependent on standby current load. This pin is internally connected to the inverting input of the PWM comparator.

Because of the pulse-by-pulse current limit capability, the maximum peak current through the Sense FET is limited, and therefore the maximum input power is restricted with vatasheet given input voltage. At startup, an dataasheet high voltage current source supplies the internal bias and charges the external capacitor Cvcc that is connected to d,o565r Vcc pin as illustrated in Figure 4.

This device is a basic platform well suited for cost effective designs of flyback converters. Cdbe datasheet pdf – datasheet pdf Cdbe datasheet pdf If the secondary side feedback circuit were to malfunction or a solder defect caused an open in the feedback path, the current through the opto-coupler transistor becomes almost zero.

In order to avoid this undesired operation, the over load protection circuit is designed to be activated after a specified time to determine whether it is a transient situation or datashwet overload situation.

TempFeedback Source Current vs.